SCTP-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32, Gauge32,
Counter32, Counter64, mib-2
FROM SNMPv2-SMI -- [RFC2578]
TimeStamp, TruthValue
FROM SNMPv2-TC -- [RFC2579]
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF -- [RFC2580]
InetAddressType, InetAddress, InetPortNumber
FROM INET-ADDRESS-MIB; -- [RFC3291]
sctpMIB MODULE-IDENTITY
LAST-UPDATED "200409020000Z" -- 2nd September 2004
ORGANIZATION "IETF SIGTRAN Working Group"
CONTACT-INFO
"
WG EMail: sigtran@ietf.org
Web Page:
http://www.ietf.org/html.charters/sigtran-charter.html
Chair: Lyndon Ong
Ciena Corporation
0480 Ridgeview Drive
Cupertino, CA 95014
USA
Tel:
Email: lyong@ciena.com
Editors: Maria-Carmen Belinchon
R&D Department
Ericsson Espana S. A.
Via de los Poblados, 13
28033 Madrid
Spain
Tel: +34 91 339 3535
Email: Maria.C.Belinchon@ericsson.com
Jose-Javier Pastor-Balbas
R&D Department
Ericsson Espana S. A.
Via de los Poblados, 13
28033 Madrid
Spain
Tel: +34 91 339 1397
Email: J.Javier.Pastor@ericsson.com
"
DESCRIPTION
"The MIB module for managing SCTP implementations.
Copyright (C) The Internet Society (2004). This version of
this MIB module is part of RFC 3873; see the RFC itself for
full legal notices. "
REVISION "200409020000Z" -- 2nd September 2004
DESCRIPTION " Initial version, published as RFC 3873"
::= { mib-2 104 }
-- the SCTP base variables group
sctpObjects OBJECT IDENTIFIER ::= { sctpMIB 1 }
sctpStats OBJECT IDENTIFIER ::= { sctpObjects 1 }
sctpParams OBJECT IDENTIFIER ::= { sctpObjects 2 }
-- STATISTICS
-- **********
-- STATE-RELATED STATISTICS
sctpCurrEstab OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of associations for which the current state is
either ESTABLISHED, SHUTDOWN-RECEIVED or SHUTDOWN-PENDING."
REFERENCE
"Section 4 in RFC2960 covers the SCTP Association state
diagram."
::= { sctpStats 1 }
sctpActiveEstabs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that associations have made a direct
transition to the ESTABLISHED state from the COOKIE-ECHOED
state: COOKIE-ECHOED -> ESTABLISHED. The upper layer initiated
the association attempt."
REFERENCE
"Section 4 in RFC2960 covers the SCTP Association state
diagram."
::= { sctpStats 2 }
sctpPassiveEstabs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that associations have made a direct
transition to the ESTABLISHED state from the CLOSED state:
CLOSED -> ESTABLISHED. The remote endpoint initiated the
association attempt."
REFERENCE
"Section 4 in RFC2960 covers the SCTP Association state
diagram."
::= { sctpStats 3 }
sctpAborteds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that associations have made a direct
transition to the CLOSED state from any state using the
primitive 'ABORT': AnyState --Abort--> CLOSED. Ungraceful
termination of the association."
REFERENCE
"Section 4 in RFC2960 covers the SCTP Association state
diagram."
::= { sctpStats 4 }
sctpShutdowns OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that associations have made a direct
transition to the CLOSED state from either the SHUTDOWN-SENT
state or the SHUTDOWN-ACK-SENT state. Graceful termination of
the association."
REFERENCE
"Section 4 in RFC2960 covers the SCTP Association state
diagram."
::= { sctpStats 5 }
-- OTHER LAYER STATISTICS
sctpOutOfBlues OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of out of the blue packets received by the host.
An out of the blue packet is an SCTP packet correctly formed,
including the proper checksum, but for which the receiver was
unable to identify an appropriate association."
REFERENCE
"Section 8.4 in RFC2960 deals with the Out-Of-The-Blue
(OOTB) packet definition and procedures."
::= { sctpStats 6 }
sctpChecksumErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of SCTP packets received with an invalid
checksum."
REFERENCE
"The checksum is located at the end of the SCTP packet as per
Section 3.1 in RFC2960. RFC3309 updates SCTP to use a 32 bit
CRC checksum."
::= { sctpStats 7 }
sctpOutCtrlChunks OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of SCTP control chunks sent (retransmissions are
not included). Control chunks are those chunks different from
DATA."
REFERENCE
"Sections 1.3.5 and 1.4 in RFC2960 refer to control chunk as
those chunks different from those that contain user
information, i.e., DATA chunks."
::= { sctpStats 8 }
sctpOutOrderChunks OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of SCTP ordered data chunks sent (retransmissions
are not included)."
REFERENCE
"Section 3.3.1 in RFC2960 defines the ordered data chunk."
::= { sctpStats 9 }
sctpOutUnorderChunks OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of SCTP unordered chunks (data chunks in which the
U bit is set to 1) sent (retransmissions are not included)."
REFERENCE
"Section 3.3.1 in RFC2960 defines the unordered data chunk."
::= { sctpStats 10 }
sctpInCtrlChunks OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of SCTP control chunks received (no duplicate
chunks included)."
REFERENCE
"Sections 1.3.5 and 1.4 in RFC2960 refer to control chunk as
those chunks different from those that contain user
information, i.e., DATA chunks."
::= { sctpStats 11 }
sctpInOrderChunks OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of SCTP ordered data chunks received (no duplicate
chunks included)."
REFERENCE
"Section 3.3.1 in RFC2960 defines the ordered data chunk."
::= { sctpStats 12 }
sctpInUnorderChunks OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of SCTP unordered chunks (data chunks in which the
U bit is set to 1) received (no duplicate chunks included)."
REFERENCE
"Section 3.3.1 in RFC2960 defines the unordered data chunk."
::= { sctpStats 13 }
sctpFragUsrMsgs OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of user messages that have to be fragmented
because of the MTU."
::= { sctpStats 14 }
sctpReasmUsrMsgs OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of user messages reassembled, after conversion
into DATA chunks."
REFERENCE
"Section 6.9 in RFC2960 includes a description of the
reassembly process."
::= { sctpStats 15 }
sctpOutSCTPPacks OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of SCTP packets sent. Retransmitted DATA chunks
are included."
::= { sctpStats 16 }
sctpInSCTPPacks OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of SCTP packets received. Duplicates are
included."
::= { sctpStats 17 }
sctpDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at which
any one or more of this general statistics counters suffered a
discontinuity. The relevant counters are the specific
instances associated with this interface of any Counter32 or
Counter64 object contained in the SCTP layer statistics
(defined below sctpStats branch). If no such discontinuities
have occurred since the last re-initialization of the local
management subsystem, then this object contains a zero value."
REFERENCE
"The inclusion of this object is recommended by RFC2578."
::= { sctpStats 18 }
-- PROTOCOL GENERAL VARIABLES
-- **************************
sctpRtoAlgorithm OBJECT-TYPE
SYNTAX INTEGER {
other(1), -- Other new one. Future use
vanj(2) -- Van Jacobson's algorithm
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The algorithm used to determine the timeout value (T3-rtx)
used for re-transmitting unacknowledged chunks."
REFERENCE
"Section 6.3.1 and 6.3.2 in RFC2960 cover the RTO calculation
and retransmission timer rules."
DEFVAL {vanj} -- vanj(2)
::= { sctpParams 1 }
sctpRtoMin OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum value permitted by a SCTP implementation for the
retransmission timeout value, measured in milliseconds. More
refined semantics for objects of this type depend upon the
algorithm used to determine the retransmission timeout value.
A retransmission time value of zero means immediate
retransmission.
The value of this object has to be lower than or equal to
stcpRtoMax's value."
DEFVAL {1000} -- milliseconds
::= { sctpParams 2 }
sctpRtoMax OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum value permitted by a SCTP implementation for the
retransmission timeout value, measured in milliseconds. More
refined semantics for objects of this type depend upon the
algorithm used to determine the retransmission timeout value.
A retransmission time value of zero means immediate re-
transmission.
The value of this object has to be greater than or equal to
stcpRtoMin's value."
DEFVAL {60000} -- milliseconds
::= { sctpParams 3 }
sctpRtoInitial OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The initial value for the retransmission timer.
A retransmission time value of zero means immediate re-
transmission."
DEFVAL {3000} -- milliseconds
::= { sctpParams 4 }
sctpMaxAssocs OBJECT-TYPE
SYNTAX Integer32 (-1 | 0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The limit on the total number of associations the entity can
support. In entities where the maximum number of associations
is dynamic, this object should contain the value -1."
::= { sctpParams 5 }
sctpValCookieLife OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid cookie life in the 4-way start-up handshake procedure."
REFERENCE
"Section 5.1.3 in RFC2960 explains the cookie generation
process. Recommended value is per section 14 in RFC2960."
DEFVAL {60000} -- milliseconds
::= { sctpParams 6 }
sctpMaxInitRetr OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of retransmissions at the start-up phase
(INIT and COOKIE ECHO chunks). "
REFERENCE
"Section 5.1.4, 5.1.6 in RFC2960 refers to Max.Init.Retransmit
parameter. Recommended value is per section 14 in RFC2960."
DEFVAL {8} -- number of attempts
::= { sctpParams 7 }
-- TABLES
-- ******
-- the SCTP Association TABLE
-- The SCTP association table contains information about each
-- association in which the local endpoint is involved.
sctpAssocTable OBJECT-TYPE
SYNTAX SEQUENCE OF SctpAssocEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing SCTP association-specific information."
::= { sctpObjects 3 }
sctpAssocEntry OBJECT-TYPE
SYNTAX SctpAssocEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"General common variables and statistics for the whole
association."
INDEX { sctpAssocId }
::= { sctpAssocTable 1 }
SctpAssocEntry ::= SEQUENCE {
sctpAssocId Unsigned32,
sctpAssocRemHostName OCTET STRING,
sctpAssocLocalPort InetPortNumber,
sctpAssocRemPort InetPortNumber,
sctpAssocRemPrimAddrType InetAddressType,
sctpAssocRemPrimAddr InetAddress,
sctpAssocHeartBeatInterval Unsigned32,
sctpAssocState INTEGER,
sctpAssocInStreams Unsigned32,
sctpAssocOutStreams Unsigned32,
sctpAssocMaxRetr Unsigned32,
sctpAssocPrimProcess Unsigned32,
sctpAssocT1expireds Counter32, -- Statistic
sctpAssocT2expireds Counter32, -- Statistic
sctpAssocRtxChunks Counter32, -- Statistic
sctpAssocStartTime TimeStamp,
sctpAssocDiscontinuityTime TimeStamp
}
sctpAssocId OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Association Identification. Value identifying the
association. "
::= { sctpAssocEntry 1 }
sctpAssocRemHostName OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The peer's DNS name. This object needs to have the same
format as the encoding in the DNS protocol. This implies that
the domain name can be up to 255 octets long, each octet being
0<=x<=255 as value with US-ASCII A-Z having a case insensitive
matching.
If no DNS domain name was received from the peer at init time
(embedded in the INIT or INIT-ACK chunk), this object is
meaningless. In such cases the object MUST contain a zero-
length string value. Otherwise, it contains the remote host
name received at init time."
::= { sctpAssocEntry 2 }
sctpAssocLocalPort OBJECT-TYPE
SYNTAX InetPortNumber (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local SCTP port number used for this association."
::= { sctpAssocEntry 3 }
sctpAssocRemPort OBJECT-TYPE
SYNTAX InetPortNumber (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The remote SCTP port number used for this association."
::= { sctpAssocEntry 4 }
sctpAssocRemPrimAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The internet type of primary remote IP address. "
::= { sctpAssocEntry 5 }
sctpAssocRemPrimAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The primary remote IP address. The type of this address is
determined by the value of sctpAssocRemPrimAddrType.
The client side will know this value after INIT_ACK message
reception, the server side will know this value when sending
INIT_ACK message. However, values will be filled in at
established(4) state."
::= { sctpAssocEntry 6 }
sctpAssocHeartBeatInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current heartbeat interval..
Zero value means no HeartBeat, even when the concerned
sctpAssocRemAddrHBFlag object is true."
DEFVAL {30000} -- milliseconds
::= { sctpAssocEntry 7 }
sctpAssocState OBJECT-TYPE
SYNTAX INTEGER {
closed(1),
cookieWait(2),
cookieEchoed(3),
established(4),
shutdownPending(5),
shutdownSent(6),
shutdownReceived(7),
shutdownAckSent(8),
deleteTCB(9)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The state of this SCTP association.
As in TCP, deleteTCB(9) is the only value that may be set by a
management station. If any other value is received, then the
agent must return a wrongValue error.
If a management station sets this object to the value
deleteTCB(9), then this has the effect of deleting the TCB (as
defined in SCTP) of the corresponding association on the
managed node, resulting in immediate termination of the
association.
As an implementation-specific option, an ABORT chunk may be
sent from the managed node to the other SCTP endpoint as a
result of setting the deleteTCB(9) value. The ABORT chunk
implies an ungraceful association shutdown."
REFERENCE
"Section 4 in RFC2960 covers the SCTP Association state
diagram."
::= { sctpAssocEntry 8 }
sctpAssocInStreams OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Inbound Streams according to the negotiation at association
start up."
REFERENCE
"Section 1.3 in RFC2960 includes a definition of stream.
Section 5.1.1 in RFC2960 covers the streams negotiation
process."
::= { sctpAssocEntry 9 }
sctpAssocOutStreams OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Outbound Streams according to the negotiation at association
start up. "
REFERENCE
"Section 1.3 in RFC2960 includes a definition of stream.
Section 5.1.1 in RFC2960 covers the streams negotiation
process."
::= { sctpAssocEntry 10 }
sctpAssocMaxRetr OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of data retransmissions in the association
context. This value is specific for each association and the
upper layer can change it by calling the appropriate
primitives. This value has to be smaller than the addition of
all the maximum number for all the paths
(sctpAssocRemAddrMaxPathRtx).
A value of zero value means no retransmissions."
DEFVAL {10} -- number of attempts
::= { sctpAssocEntry 11 }
sctpAssocPrimProcess OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies the system level process which holds
primary responsibility for the SCTP association.
Wherever possible, this should be the system's native unique
identification number. The special value 0 can be used to
indicate that no primary process is known.
Note that the value of this object can be used as a pointer
into the swRunTable of the HOST-RESOURCES-MIB(if the value is
smaller than 2147483647) or into the sysApplElmtRunTable of
the SYSAPPL-MIB."
::= { sctpAssocEntry 12 }
-- Association Statistics
sctpAssocT1expireds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The T1 timer determines how long to wait for an
acknowledgement after sending an INIT or COOKIE-ECHO chunk.
This object reflects the number of times the T1 timer expires
without having received the acknowledgement.
Discontinuities in the value of this counter can occur at re-
initialization of the management system, and at other times as
indicated by the value of sctpAssocDiscontinuityTime."
REFERENCE
"Section 5 in RFC2960."
::= { sctpAssocEntry 13 }
sctpAssocT2expireds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The T2 timer determines how long to wait for an
acknowledgement after sending a SHUTDOWN or SHUTDOWN-ACK
chunk. This object reflects the number of times that T2- timer
expired.
Discontinuities in the value of this counter can occur at re-
initialization of the management system, and at other times as
indicated by the value of sctpAssocDiscontinuityTime."
REFERENCE
"Section 9.2 in RFC2960."
::= { sctpAssocEntry 14 }
sctpAssocRtxChunks OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When T3-rtx expires, the DATA chunks that triggered the T3
timer will be re-sent according with the retransmissions
rules. Every DATA chunk that was included in the SCTP packet
that triggered the T3-rtx timer must be added to the value of
this counter.
Discontinuities in the value of this counter can occur at re-
initialization of the management system, and at other times as
indicated by the value of sctpAssocDiscontinuityTime."
REFERENCE
"Section 6 in RFC2960 covers the retransmission process and
rules."
::= { sctpAssocEntry 15 }
sctpAssocStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time that the association
represented by this row enters the ESTABLISHED state, i.e.,
the sctpAssocState object is set to established(4). The
value of this object will be zero:
- before the association enters the established(4)
state, or
- if the established(4) state was entered prior to
the last re-initialization of the local network management
subsystem."
::= { sctpAssocEntry 16 }
sctpAssocDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at which
any one or more of this SCTP association counters suffered a
discontinuity. The relevant counters are the specific
instances associated with this interface of any Counter32 or
Counter64 object contained in the sctpAssocTable or
sctpLocalAddrTable or sctpRemAddrTable. If no such
discontinuities have occurred since the last re-initialization
of the local management subsystem, then this object contains a
zero value. "
REFERENCE
"The inclusion of this object is recommended by RFC2578."
::= { sctpAssocEntry 17 }
-- Expanded tables: Including Multi-home feature
-- Local Address TABLE
-- *******************
sctpAssocLocalAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF SctpAssocLocalAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Expanded table of sctpAssocTable based on the AssocId index.
This table shows data related to each local IP address which
is used by this association."
::= { sctpObjects 4 }
sctpAssocLocalAddrEntry OBJECT-TYPE
SYNTAX SctpAssocLocalAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Local information about the available addresses. There will
be an entry for every local IP address defined for this
association.
Implementors need to be aware that if the size of
sctpAssocLocalAddr exceeds 114 octets then OIDs of column
instances in this table will have more than 128 sub-
identifiers and cannot be accessed using SNMPv1, SNMPv2c, or
SNMPv3."
INDEX { sctpAssocId, -- shared index
sctpAssocLocalAddrType,
sctpAssocLocalAddr }
::= { sctpAssocLocalAddrTable 1 }
SctpAssocLocalAddrEntry ::= SEQUENCE {
sctpAssocLocalAddrType InetAddressType,
sctpAssocLocalAddr InetAddress,
sctpAssocLocalAddrStartTime TimeStamp
}
sctpAssocLocalAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Internet type of local IP address used for this association."
::= { sctpAssocLocalAddrEntry 1 }
sctpAssocLocalAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of a local IP address available for this
association. The type of this address is determined by the
value of sctpAssocLocalAddrType."
::= { sctpAssocLocalAddrEntry 2 }
sctpAssocLocalAddrStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time that this row was
created."
::= { sctpAssocLocalAddrEntry 3 }
-- Remote Addresses TABLE
-- **********************
sctpAssocRemAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF SctpAssocRemAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Expanded table of sctpAssocTable based on the AssocId index.
This table shows data related to each remote peer IP address
which is used by this association."
::= { sctpObjects 5 }
sctpAssocRemAddrEntry OBJECT-TYPE
SYNTAX SctpAssocRemAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about the most important variables for every
remote IP address. There will be an entry for every remote IP
address defined for this association.
Implementors need to be aware that if the size of
sctpAssocRemAddr exceeds 114 octets then OIDs of column
instances in this table will have more than 128 sub-
identifiers and cannot be accessed using SNMPv1, SNMPv2c, or
SNMPv3."
INDEX { sctpAssocId, -- shared index
sctpAssocRemAddrType,
sctpAssocRemAddr }
::= { sctpAssocRemAddrTable 1 }
SctpAssocRemAddrEntry ::= SEQUENCE {
sctpAssocRemAddrType InetAddressType,
sctpAssocRemAddr InetAddress,
sctpAssocRemAddrActive TruthValue,
sctpAssocRemAddrHBActive TruthValue,
sctpAssocRemAddrRTO Unsigned32,
sctpAssocRemAddrMaxPathRtx Unsigned32,
sctpAssocRemAddrRtx Counter32, -- Statistic
sctpAssocRemAddrStartTime TimeStamp
}
sctpAssocRemAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Internet type of a remote IP address available for this
association."
::= { sctpAssocRemAddrEntry 1 }
sctpAssocRemAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of a remote IP address available for this
association. The type of this address is determined by the
value of sctpAssocLocalAddrType."
::= { sctpAssocRemAddrEntry 2 }
sctpAssocRemAddrActive OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives information about the reachability of this
specific remote IP address.
When the object is set to 'true' (1), the remote IP address is
understood as Active. Active means that the threshold of no
answers received from this IP address has not been reached.
When the object is set to 'false' (2), the remote IP address
is understood as Inactive. Inactive means that either no
heartbeat or any other message was received from this address,
reaching the threshold defined by the protocol."
REFERENCE
"The remote transport states are defined as Active and
Inactive in the SCTP, RFC2960."
::= { sctpAssocRemAddrEntry 3 }
sctpAssocRemAddrHBActive OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether the optional Heartbeat check
associated to one destination transport address is activated
or not (value equal to true or false, respectively). "
::= { sctpAssocRemAddrEntry 4 }
sctpAssocRemAddrRTO OBJECT-TYPE -- T3-rtx- Timer
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current Retransmission Timeout. T3-rtx timer as defined
in the protocol SCTP."
REFERENCE
"Section 6.3 in RFC2960 deals with the Retransmission Timer
Management."
::= { sctpAssocRemAddrEntry 5 }
sctpAssocRemAddrMaxPathRtx OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum number of DATA chunks retransmissions allowed to a
remote IP address before it is considered inactive, as defined
in RFC2960."
REFERENCE
"Section 8.2, 8.3 and 14 in RFC2960."
DEFVAL {5} -- number of attempts
::= { sctpAssocRemAddrEntry 6 }
-- Remote Address Statistic
sctpAssocRemAddrRtx OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of DATA chunks retransmissions to this specific IP
address. When T3-rtx expires, the DATA chunk that triggered
the T3 timer will be re-sent according to the retransmissions
rules. Every DATA chunk that is included in a SCTP packet and
was transmitted to this specific IP address before, will be
included in this counter.
Discontinuities in the value of this counter can occur at re-
initialization of the management system, and at other times as
indicated by the value of sctpAssocDiscontinuityTime."
::= { sctpAssocRemAddrEntry 7 }
sctpAssocRemAddrStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time that this row was
created."
::= { sctpAssocRemAddrEntry 8 }
-- ASSOCIATION INVERSE TABLE
-- *************************
-- BY LOCAL PORT
sctpLookupLocalPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF SctpLookupLocalPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"With the use of this table, a list of associations which are
using the specified local port can be retrieved."
::= { sctpObjects 6 }
sctpLookupLocalPortEntry OBJECT-TYPE
SYNTAX SctpLookupLocalPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is indexed by local port and association ID.
Specifying a local port, we would get a list of the
associations whose local port is the one specified."
INDEX { sctpAssocLocalPort,
sctpAssocId }
::= { sctpLookupLocalPortTable 1 }
SctpLookupLocalPortEntry::= SEQUENCE {
sctpLookupLocalPortStartTime TimeStamp
}
sctpLookupLocalPortStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time that this row was created.
As the table will be created after the sctpAssocTable
creation, this value could be equal to the sctpAssocStartTime
object from the main table."
::= { sctpLookupLocalPortEntry 1 }
-- BY REMOTE PORT
sctpLookupRemPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF SctpLookupRemPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"With the use of this table, a list of associations which are
using the specified remote port can be got"
::= { sctpObjects 7 }
sctpLookupRemPortEntry OBJECT-TYPE
SYNTAX SctpLookupRemPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is indexed by remote port and association ID.
Specifying a remote port we would get a list of the
associations whose local port is the one specified "
INDEX { sctpAssocRemPort,
sctpAssocId }
::= { sctpLookupRemPortTable 1 }
SctpLookupRemPortEntry::= SEQUENCE {
sctpLookupRemPortStartTime TimeStamp
}
sctpLookupRemPortStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time that this row was created.
As the table will be created after the sctpAssocTable
creation, this value could be equal to the sctpAssocStartTime
object from the main table."
::= { sctpLookupRemPortEntry 1 }
-- BY REMOTE HOST NAME
sctpLookupRemHostNameTable OBJECT-TYPE
SYNTAX SEQUENCE OF SctpLookupRemHostNameEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"With the use of this table, a list of associations with that
particular host can be retrieved."
::= { sctpObjects 8 }
sctpLookupRemHostNameEntry OBJECT-TYPE
SYNTAX SctpLookupRemHostNameEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is indexed by remote host name and association ID.
Specifying a host name we would get a list of the associations
specifying that host name as the remote one.
Implementors need to be aware that if the size of
sctpAssocRemHostName exceeds 115 octets then OIDs of column
instances in this table will have more than 128 sub-
identifiers and cannot be accessed using SNMPv1, SNMPv2c, or
SNMPv3."
INDEX { sctpAssocRemHostName,
sctpAssocId }
::= { sctpLookupRemHostNameTable 1 }
SctpLookupRemHostNameEntry::= SEQUENCE {
sctpLookupRemHostNameStartTime TimeStamp
}
sctpLookupRemHostNameStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time that this row was created.
As the table will be created after the sctpAssocTable
creation, this value could be equal to the sctpAssocStartTime
object from the main table."
::= { sctpLookupRemHostNameEntry 1 }
-- BY REMOTE PRIMARY IP ADDRESS
sctpLookupRemPrimIPAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF SctpLookupRemPrimIPAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"With the use of this table, a list of associations that have
the specified IP address as primary within the remote set of
active addresses can be retrieved."
::= { sctpObjects 9 }
sctpLookupRemPrimIPAddrEntry OBJECT-TYPE
SYNTAX SctpLookupRemPrimIPAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is indexed by primary address and association ID.
Specifying a primary address, we would get a list of the
associations that have the specified remote IP address marked
as primary.
Implementors need to be aware that if the size of
sctpAssocRemPrimAddr exceeds 114 octets then OIDs of column
instances in this table will have more than 128 sub-
identifiers and cannot be accessed using SNMPv1, SNMPv2c, or
SNMPv3."
INDEX { sctpAssocRemPrimAddrType,
sctpAssocRemPrimAddr,
sctpAssocId }
::= { sctpLookupRemPrimIPAddrTable 1 }
SctpLookupRemPrimIPAddrEntry::= SEQUENCE {
sctpLookupRemPrimIPAddrStartTime TimeStamp
}
sctpLookupRemPrimIPAddrStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of SysUpTime at the time that this row was created.
As the table will be created after the sctpAssocTable
creation, this value could be equal to the sctpAssocStartTime
object from the main table."
::= { sctpLookupRemPrimIPAddrEntry 1 }
-- BY REMOTE IP ADDRESS
sctpLookupRemIPAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF SctpLookupRemIPAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"With the use of this table, a list of associations that have
the specified IP address as one of the remote ones can be
retrieved. "
::= { sctpObjects 10 }
sctpLookupRemIPAddrEntry OBJECT-TYPE
SYNTAX SctpLookupRemIPAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is indexed by a remote IP address and association
ID. Specifying an IP address we would get a list of the
associations that have the specified IP address included
within the set of remote IP addresses."
INDEX { sctpAssocRemAddrType,
sctpAssocRemAddr,
sctpAssocId }
::= { sctpLookupRemIPAddrTable 1 }
SctpLookupRemIPAddrEntry::= SEQUENCE {
sctpLookupRemIPAddrStartTime TimeStamp
}
sctpLookupRemIPAddrStartTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of SysUpTime at the time that this row was created.
As the table will be created after the sctpAssocTable
creation, this value could be equal to the sctpAssocStartTime
object from the main table."
::= { sctpLookupRemIPAddrEntry 1 }
-- 4.1 Conformance Information
sctpMibConformance OBJECT IDENTIFIER ::= { sctpMIB 2 }
sctpMibCompliances OBJECT IDENTIFIER ::= { sctpMibConformance 1 }
sctpMibGroups OBJECT IDENTIFIER ::= { sctpMibConformance 2 }
-- 4.1.1 Units of conformance
--
-- MODULE GROUPS
--
sctpLayerParamsGroup OBJECT-GROUP
OBJECTS { sctpRtoAlgorithm,
sctpRtoMin,
sctpRtoMax,
sctpRtoInitial,
sctpMaxAssocs,
sctpValCookieLife,
sctpMaxInitRetr
}
STATUS current
DESCRIPTION
"Common parameters for the SCTP layer, i.e., for all the
associations. They can usually be referred to as configuration
parameters."
::= { sctpMibGroups 1 }
sctpStatsGroup OBJECT-GROUP
OBJECTS { sctpCurrEstab,
sctpActiveEstabs,
sctpPassiveEstabs,
sctpAborteds,
sctpShutdowns,
sctpOutOfBlues,
sctpChecksumErrors,
sctpOutCtrlChunks,
sctpOutOrderChunks,
sctpOutUnorderChunks,
sctpInCtrlChunks,
sctpInOrderChunks,
sctpInUnorderChunks,
sctpFragUsrMsgs,
sctpReasmUsrMsgs,
sctpOutSCTPPacks,
sctpInSCTPPacks,
sctpDiscontinuityTime,
sctpAssocT1expireds,
sctpAssocT2expireds,
sctpAssocRtxChunks,
sctpAssocRemAddrRtx
}
STATUS current
DESCRIPTION
"Statistics group. It includes the objects to collect state
changes in the SCTP protocol local layer and flow control
statistics."
::= { sctpMibGroups 2 }
sctpPerAssocParamsGroup OBJECT-GROUP
OBJECTS { sctpAssocRemHostName,
sctpAssocLocalPort,
sctpAssocRemPort,
sctpAssocRemPrimAddrType,
sctpAssocRemPrimAddr,
sctpAssocHeartBeatInterval,
sctpAssocState,
sctpAssocInStreams,
sctpAssocOutStreams,
sctpAssocMaxRetr,
sctpAssocPrimProcess,
sctpAssocStartTime,
sctpAssocDiscontinuityTime,
sctpAssocLocalAddrStartTime,
sctpAssocRemAddrActive,
sctpAssocRemAddrHBActive,
sctpAssocRemAddrRTO,
sctpAssocRemAddrMaxPathRtx,
sctpAssocRemAddrStartTime
}
STATUS current
DESCRIPTION
"The SCTP group of objects to manage per-association
parameters. These variables include all the SCTP basic
features."
::= { sctpMibGroups 3 }
sctpPerAssocStatsGroup OBJECT-GROUP
OBJECTS
{ sctpAssocT1expireds,
sctpAssocT2expireds,
sctpAssocRtxChunks,
sctpAssocRemAddrRtx
}
STATUS current
DESCRIPTION
"Per Association Statistics group. It includes the objects to
collect flow control statistics per association."
::= { sctpMibGroups 4 }
sctpInverseGroup OBJECT-GROUP
OBJECTS { sctpLookupLocalPortStartTime,
sctpLookupRemPortStartTime,
sctpLookupRemHostNameStartTime,
sctpLookupRemPrimIPAddrStartTime,
sctpLookupRemIPAddrStartTime
}
STATUS current
DESCRIPTION
"Objects used in the inverse lookup tables."
::= { sctpMibGroups 5 }
-- 4.1.2 Compliance Statements
--
-- MODULE COMPLIANCES
--
sctpMibCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities which implement
this SCTP MIB Module.
There are a number of INDEX objects that cannot be represented
in the form of OBJECT clauses in SMIv2, but for which we have
the following compliance requirements, expressed in OBJECT
clause form in this description clause:
-- OBJECT sctpAssocLocalAddrType
-- SYNTAX InetAddressType {ipv4(1), ipv6(2)}
-- DESCRIPTION
-- It is only required to have IPv4 and IPv6 addresses without
-- zone indices.
-- The address with zone indices is required if an
-- implementation can connect multiple zones.
--
-- OBJECT sctpAssocLocalAddr
-- SYNTAX InetAddress (SIZE(4|16))
-- DESCRIPTION
-- An implementation is only required to support globally
-- unique IPv4 and IPv6 addresses.
--
-- OBJECT sctpAssocRemAddrType
-- SYNTAX InetAddressType {ipv4(1), ipv6(2)}
-- DESCRIPTION
-- It is only required to have IPv4 and IPv6 addresses without
-- zone indices.
-- The address with zone indices is required if an
-- implementation can connect multiple zones.
--
-- OBJECT sctpAssocRemAddr
-- SYNTAX InetAddress (SIZE(4|16))
-- DESCRIPTION
-- An implementation is only required to support globally
-- unique IPv4 and IPv6 addresses.
--
" -- closes DESCRIPTION clause of MODULE-COMPLIANCE
MODULE -- this module
MANDATORY-GROUPS { sctpLayerParamsGroup,
sctpPerAssocParamsGroup,
sctpStatsGroup,
sctpPerAssocStatsGroup
}
OBJECT sctpAssocRemPrimAddrType
SYNTAX InetAddressType { ipv4(1),
ipv6(2)
}
DESCRIPTION
"It is only required to have IPv4 and IPv6 addresses
without zone indices.
The address with zone indices is required if an
implementation can connect multiple zones."
OBJECT sctpAssocRemPrimAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is only required to support globally
unique IPv4 and globally unique IPv6 addresses."
OBJECT sctpAssocState
WRITE-SYNTAX INTEGER { deleteTCB(9) }
MIN-ACCESS read-only
DESCRIPTION
"Only the deleteTCB(9) value MAY be set by a management
station at most. A read-only option is also considered to
be compliant with this MIB module description."
GROUP sctpInverseGroup
DESCRIPTION
"Objects used in inverse lookup tables. This should be
implemented, at the discretion of the implementers, for
easier lookups in the association tables"
::= { sctpMibCompliances 1 }
END
Mini Shell